HS code chapter 74: Copper and articles thereof
Chapter 74 of the Harmonized Tariff Schedule of the United States: Copper and articles thereof. It holds 16 headings, 7401 to 7419, and 136 ten digit US HTS codes.
General duty rates in the chapter run from Free to 3%, and 22 codes (16%) enter free of general duty. The highest percent rates sit under 7407 (3%), 7408 (3%), 7409 (3%).
The 16 headings in chapter 74
Each four digit heading with its HTS codes and the span of their general duty rates. 2 headings hold a single code, shown in full below.
| Heading | Description | HTS codes | General duty |
|---|---|---|---|
| 7401 | Copper mattes; cement copper (precipitated copper) | 1 | Free |
| 7402 | Unrefined copper; copper anodes for electrolytic refining | 1 | Free |
| 7403 | Refined copper and copper alloys, unwrought (other than master alloys of heading 7405) | 8 | 1% |
| 7404 | Copper waste and scrap | 10 | Free |
| 7405 | Master alloys of copper | 3 | Free |
| 7406 | Copper powders and flakes | 2 | Free |
| 7407 | Copper bars, rods and profiles | 15 | 1% to 3% |
| 7408 | Copper wire | 9 | 1% to 3% |
| 7409 | Copper plates, sheets and strip, of a thickness exceeding 0.15 mm | 29 | 1% to 3% |
| 7410 | Copper foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0.15 mm | 8 | 1% to 3% |
| 7411 | Copper tubes and pipes | 8 | 1.4% to 3% |
| 7412 | Copper tube or pipe fittings (for example couplings, elbows, sleeves) | 8 | 3% |
| 7413 | Stranded wire, cables, plaited bands and the like, including slings and similar articles, of copper, not electrically insulated | 3 | 2% to 3% |
| 7415 | Nails, tacks, drawing pins, staples (other than those of heading 8305) and similar articles, of copper or of iron or steel with heads of copper; screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers (including spring washers) and similar articles, of copper | 8 | 1.4% to 3% |
| 7418 | Table, kitchen or other household articles and parts thereof, of copper; pot scourers and scouring or polishing pads, gloves and the like, of copper; sanitary ware and parts thereof, of copper | 11 | 3% |
| 7419 | Other articles of copper | 12 | Free to 3% |
2 headings with a single HTS code
These headings have one ten digit code each, so the code and its rates are here in full.
7401: Copper mattes
“Copper mattes; cement copper (precipitated copper).”
- HTS code
- 7401.00.00.00
- General
- Free
- Column 2
- 6%
- Units
- kg
- Special
- None listed
7402: Unrefined copper
“Unrefined copper; copper anodes for electrolytic refining.”
- HTS code
- 7402.00.00.00
- General
- Free
- Column 2
- 6%
- Units
- kg, Cu kg
- Special
- None listed
The most common general duty rates in chapter 74
| General duty rate | HTS codes |
|---|---|
| 3% | 70 |
| Free | 22 |
| 1% | 17 |
| 1.9% | 9 |
| 1.5% | 4 |
| 1.7% | 4 |
| 2.2% | 4 |
| 1.4% | 3 |
Chapter 74 notes
The legal notes at the head of the chapter decide what it covers and what it leaves to other chapters, so read them before you settle on a heading. They are the schedule’s own text, 455 words.
Read the chapter 74 notes
Note
1. In this chapter the following expressions have the meanings hereby assigned to them:
(a) Refined copper
Metal containing at least 99.85 percent by weight of copper; or
Metal containing at least 97.5 percent by weight of copper, provided that the content by weight of any other element does not exceed the limit specified in the following table:
(b) Copper alloys
Metallic substances other than unrefined copper in which copper predominates by weight over each of the other elements, provided that:
(i) The content by weight of at least one of the other elements is greater than the limit specified in the foregoing table; or
(ii) The total content by weight of such other elements exceeds 2.5 percent.
(c) Master alloys
Alloys containing with other elements more than 10 percent by weight of copper, not usefully malleable and commonly used as an additive in the manufacture of other alloys or as deoxidants, desulfurizing agents or for similar uses in the metallurgy of nonferrous metals. However, copper phosphide (phosphor copper) containing more than 15 percent by weight of phosphorus falls in heading 2853.
Subheading Note
1. In this chapter the following expressions have the meanings hereby assigned to them:
(a) Copper-zinc base alloys (brasses)
Alloys of copper and zinc, with or without other elements. When other elements are present:
- zinc predominates by weight over each of such other elements;
- any nickel content by weight is less than 5 percent (see copper-nickel-zinc alloys (nickel silvers)); and
- any tin content by weight is less than 3 percent (see copper-tin alloys (bronzes)).
(b) Copper-tin base alloys (bronzes)
Alloys of copper and tin, with or without other elements. When other elements are present, tin predominates by weight over each of such other elements, except that when the tin content is 3 percent or more the zinc content by weight may exceed that of tin but must be less than 10 percent.
(c) Copper-nickel-zinc base alloys (nickel silvers)
Alloys of copper, nickel and zinc, with or without other elements. The nickel content is 5 percent or more by weight (see copper-zinc alloys (brasses)).
(d) Copper-nickel base alloys
Alloys of copper and nickel, with or without other elements but in any case containing by weight not more than 1 percent of zinc. When other elements are present, nickel predominates by weight over each of such other elements.
Additional U.S. Note
1. The deduction provided for in additional U.S. note 1 to chapter 26 shall apply to cement copper and copper precipitates of subheading 7401.20.
Statistical Note
1. For the purposes of this chapter, the term "beryllium copper master alloy" refers to master alloys which contain by weight at least 3 percent but not more than 10 percent beryllium.
Section XV: the 11 chapters
- Chapter 72: Iron and steel
- Chapter 73: Articles of iron or steel
- Chapter 74: Copper and articles thereof (this chapter)
- Chapter 75: Nickel and articles thereof
- Chapter 76: Aluminum and articles thereof
- Chapter 78: Lead and articles thereof
- Chapter 79: Zinc and articles thereof
- Chapter 80: Tin and articles thereof
- Chapter 81: Other base metals; cermets; articles thereof
- Chapter 82: Tools, implements, cutlery, spoons and forks, of base metal; parts thereof of base metal
- Chapter 83: Miscellaneous articles of base metal
Before you file
The importer is responsible for the classification it declares, and a licensed customs broker confirms it. Warp is not a customs broker, and these pages are not customs advice. The rates here are the schedule’s own columns: additional duties that depend on the country of origin, such as Section 301, sit in chapter 99 and are not in them, and neither are the entry fees. The landed cost calculator adds the ones it covers, and the HTS code lookup searches every line by product.
Source: Harmonized Tariff Schedule of the United States, US International Trade Commission, Revision 23 (2026). Codes, descriptions, duty rates and units read November 14, 2026. Chapter notes read November 16, 2026.