Section XV: Base metals and articles of base metal

HS code chapter 76: Aluminum and articles thereof

Chapter 76 of the Harmonized Tariff Schedule of the United States: Aluminum and articles thereof. It holds 16 headings, 7601 to 7616, and 124 ten digit US HTS codes.

General duty rates in the chapter run from Free to 6.5%, and 18 codes (15%) enter free of general duty. The highest percent rates sit under 7606 (6.5%), 7616 (6%), 7607 (5.8%).

16Headings
124US HTS codes
Free to 6.5%General duty
15%Codes free

The 16 headings in chapter 76

Each four digit heading with its HTS codes and the span of their general duty rates. 2 headings hold a single code, shown in full below.

HeadingDescriptionHTS codesGeneral duty
7601Unwrought aluminum13Free to 2.6%
7602Aluminum waste and scrap5Free
7603Aluminum powders and flakes23.9% to 5%
7604Aluminum bars, rods and profiles131.5% to 5%
7605Aluminum wire42.6% to 4.2%
7606Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm192.7% to 6.5%
7607Aluminum foil (whether or not printed, or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0.2 mm11Free to 5.8%
7608Aluminum tubes and pipes45.7%
7609Aluminum tube or pipe fittings (for example, couplings, elbows, sleeves)15.7%
7610Aluminum structures (excluding prefabricated buildings of heading 9406) and parts of structures (for example, bridges and bridge-sections, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, balustrades, pillars and columns); aluminum plates, rods, profiles, tubes and the like, prepared for use in structures75.7%
7611Aluminum reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 liters, whether or not lined or heat insulated, but not fitted with mechanical or thermal equipment22.6%
7612Aluminum casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 liters, whether or not lined or heat insulated, but not fitted with mechanical or thermal equipment6Free to 5.7%
7613Aluminum containers for compressed or liquefied gas15%
7614Stranded wire, cables, plaited bands and the like, including slings and similar articles, of aluminum, not electrically insulated64.9% to 5.7%
7615Table, kitchen or other household articles and parts thereof, of aluminum; pot scourers and scouring or polishing pads, gloves and the like, of aluminum; sanitary ware and parts thereof, of aluminum133.1% to 3.8%
7616Other articles of aluminum17Free to 6%

2 headings with a single HTS code

These headings have one ten digit code each, so the code and its rates are here in full.

7609: Aluminum tube or pipe fittings

“Aluminum tube or pipe fittings (for example, couplings, elbows, sleeves).”

HTS code
7609.00.00.00
General
5.7%
Column 2
45%
Units
kg
Special
Free (A,AU,B,BH,CL,CO,D,E,IL,JO,KR,MA,OM,P,PA,PE,S,SG)
Price it

7613: Aluminum containers for compressed or liquefied gas

“Aluminum containers for compressed or liquefied gas.”

HTS code
7613.00.00.00
General
5%
Column 2
25%
Units
No.
Special
Free (A,AU,BH,CL,CO,D,E,IL,JO,KR,MA,OM,P,PA,PE,S,SG)
Price it

The most common general duty rates in chapter 76

General duty rateHTS codes
3%21
5.7%20
Free18
3.1%12
2.6%10
2.5%9
4.9%5
5%5

Chapter 76 notes

The legal notes at the head of the chapter decide what it covers and what it leaves to other chapters, so read them before you settle on a heading. They are the schedule’s own text, 597 words.

Read the chapter 76 notes

Subheading Notes

1. In this chapter the following expressions have the meanings hereby assigned to them:

(a) Aluminum, not alloyed

Metal containing by weight at least 99 percent of aluminum, provided that the content by weight of any other element does not exceed the limit specified in the following table:

(b) Aluminum alloys

Metallic substances in which aluminum predominates by weight over each of the other elements, provided that:

(i) The content by weight of at least one of the other elements or of iron plus silicon taken together is greater than the limit specified in the foregoing table; or

(ii) The total content by weight of such other elements exceeds 1 percent.

2. Notwithstanding the provisions of note 9(c) to section XV, for the purposes of subheading 7616.91 the term "wire" applies only to products, whether or not in coils, of any cross-sectional shape, of which no cross-sectional dimension exceeds 6 mm.

Additional U.S. Note

1. For the purposes of heading 7608, the rate of duty "Free (C)" appearing in the "Special" subcolumn applies only to tubes and pipes with attached fittings, suitable for conducting gases or liquids.

Statistical Notes

1. For the purposes of this chapter, the term "aluminum vanadium master alloy" refers to aluminum alloys which contain by weight 20 percent or more of vanadium.

2. For the purposes of this chapter, the term ?aluminum can stock? refers to sheets and strip in coils, of alloys of aluminum in which either manganese or magnesium predominates by weight over each of the other alloying elements, not painted, over 0.175 mm but not over 0.432 mm in thickness, and over 254 mm in width, comprising ?body stock? and ?lid stock? as specified below:

(a) The term ?body stock? refers to aluminum can stock (i) in which either manganese or magnesium predominates by weight over each of the other alloying elements; and (ii) designated as series 3xxx in the Aluminum Association?s specifications of registered alloys; and (iii) having a minimum tensile strength of 262 MPa.

(b) The term ?lid stock? refers to aluminum can stock (i) in which magnesium predominates by weight over each of the other alloying elements; and (ii) designated as series 5xxx in the Aluminum Association?s specifications of registered alloys; and (iii) having a minimum tensile strength of 345 MPa.

3. For the purposes of statistical reporting number 7601.20.9080, "sheet ingot" (slabs) refers to aluminum alloys with a rectangular cross-section suitable to be manufactured into other products.

4. For the purposes of statistical reporting number 7601.20.9085, "foundry ingot" refers to large castings of aluminum alloys of various shapes other than sheets or slabs to be melted for further processing.

5. For statistical reporting purposes under subheading 7602.00.00, the term ?recyclable aluminum? refers to materials that are obsolete, previously used, off-specification, surplus, or incidentally produced and are collected and sorted for processing into a specification-grade commodity. Recyclable materials may also be considered as scrap but do not include solid waste or residue.

6. For the purposes of statistical reporting numbers 7604.29.3030, 7604.29.5020 and 7606.12.3015, ?high-strength heat-treatable alloys? refers to aluminum containing by weight 7.0 percent or less of copper or 10.0 percent or less of zinc, and/or are designated as series 2xxx or 7xxx (except 7072) in the Aluminum Association?s specifications of registered alloys.

7. For the purposes of statistical reporting numbers 7604.21.0010, 7604.29.1010, 7604.29.3060, 7604.29.5050, 7606.12.3025 and 7606.12.3091, ?heat-treatable industrial alloys? refers to aluminum containing by weight 3.0 percent or less of magnesium and 3.0 percent or less of silicon, and/or are designated as series 6xxx in the Aluminum Association?s specifications of registered alloys.

Section XV: the 11 chapters

  • Chapter 72: Iron and steel
  • Chapter 73: Articles of iron or steel
  • Chapter 74: Copper and articles thereof
  • Chapter 75: Nickel and articles thereof
  • Chapter 76: Aluminum and articles thereof (this chapter)
  • Chapter 78: Lead and articles thereof
  • Chapter 79: Zinc and articles thereof
  • Chapter 80: Tin and articles thereof
  • Chapter 81: Other base metals; cermets; articles thereof
  • Chapter 82: Tools, implements, cutlery, spoons and forks, of base metal; parts thereof of base metal
  • Chapter 83: Miscellaneous articles of base metal

Before you file

The importer is responsible for the classification it declares, and a licensed customs broker confirms it. Warp is not a customs broker, and these pages are not customs advice. The rates here are the schedule’s own columns: additional duties that depend on the country of origin, such as Section 301, sit in chapter 99 and are not in them, and neither are the entry fees. The landed cost calculator adds the ones it covers, and the HTS code lookup searches every line by product.

Source: Harmonized Tariff Schedule of the United States, US International Trade Commission, Revision 23 (2026). Codes, descriptions, duty rates and units read November 14, 2026. Chapter notes read November 16, 2026.