Section XVI: Machinery and mechanical appliances

HS code chapter 85: Electrical machinery and equipment and parts thereof

Chapter 85 of the Harmonized Tariff Schedule of the United States: Electrical machinery and equipment and parts thereof; sound recorders and reproducers, television image and sound recorders and reproducers, and parts and accessories of such articles. It holds 48 headings, 8501 to 8549, and 982 ten digit US HTS codes.

General duty rates in the chapter run from Free to 15%, and 566 codes (58%) enter free of general duty. The highest percent rates sit under 8540 (15%), 8513 (12.5%), 8501 (6.7%).

48Headings
982US HTS codes
Free to 15%General duty
58%Codes free

The 48 headings in chapter 85

Each four digit heading with its HTS codes and the span of their general duty rates. One heading holds a single code, shown in full below.

HeadingDescriptionHTS codesGeneral duty
8501Electric motors and generators (excluding generating sets)71Free to 6.7%
8502Electric generating sets and rotary converters122% to 3%
8503Parts suitable for use solely or principally with the machines of heading 8501 or 850211Free to 6.5%
8504Electrical transformers, static converters (for example, rectifiers) and inductors; parts thereof54Free to 6.6%
8505Electromagnets; permanent magnets and articles intended to become permanent magnets after magnetization; electromagnetic or permanent magnet chucks, clamps and similar holding devices; electromagnetic couplings, clutches and brakes; electromagnetic lifting heads; parts thereof13Free to 4.9%
8506Primary cells and primary batteries; parts thereof142.7%
8507Electric storage batteries, including separators therefor, whether or not rectangular (including square); parts thereof192.5% to 3.5%
8508Vacuum cleaners; parts thereof4Free
8509Electromechanical domestic appliances, with self-contained electric motor, other than vacuum cleaners of heading 8508; parts thereof16Free to 4.2%
8510Shavers, hair clippers and hair-removing appliances, with self-contained electric motor; parts thereof9Free to 4.2%
8511Electrical ignition or starting equipment of a kind used for spark-ignition or compression-ignition internal combustion engines (for example, ignition magnetos, magneto-dynamos, ignition coils, spark plugs and glow plugs, starter motors); generators (for example, dynamos, alternators) and cut-outs of a kind used in conjunction with such engines; parts thereof13Free to 3.1%
8512Electrical lighting or signaling equipment (excluding articles of heading 8539), windshield wipers, defrosters and demisters, of a kind used for cycles or motor vehicles; parts thereof16Free to 2.7%
8513Portable electric lamps designed to function by their own source of energy (for example, dry batteries, storage batteries, magnetos), other than lighting equipment of heading 8512; parts thereof43.5% to 12.5%
8514Industrial or laboratory electric furnaces and ovens (including those functioning by induction or dielectric loss); other industrial or laboratory equipment for the heat treatment of materials by induction or dielectric loss; parts thereof14Free to 4.2%
8515Electric (including electrically heated gas), laser or other light or photon beam, ultrasonic, electron beam, magnetic pulse or plasma arc soldering, brazing or welding machines and apparatus, whether or not capable of cutting; electric machines and apparatus for hot spraying of metals or cermets; parts thereof12Free to 2.5%
8516Electric instantaneous or storage water heaters and immersion heaters; electric space heating apparatus and soil heating apparatus; electrothermic hairdressing apparatus (for example, hair dryers, hair curlers, curling tong heaters) and hand dryers; electric flatirons; other electrothermic appliances of a kind used for domestic purposes; electric heating resistors, other than those of heading 8545; parts thereof43Free to 5.3%
8517Telephone sets, including smartphones and other telephones for cellular networks or for other wireless networks; other apparatus for the transmission or reception of voice, images or other data, including apparatus for communication in a wired or wireless network (such as a local or wide area network), other than transmission or reception apparatus of heading 8443, 8525, 8527 or 8528; parts thereof15Free
8518Microphones and stands therefor; loudspeakers, whether or not mounted in their enclosures; headphones and earphones, whether or not combined with a microphone, and sets consisting of a microphone and one or more loudspeakers; audio-frequency electric amplifiers; electric sound amplifier sets; parts thereof16Free
8519Sound recording or reproducing apparatus15Free to 3.9%
8521Video recording or reproducing apparatus, whether or not incorporating a video tuner4Free
8522Parts and accessories suitable for use solely or principally with the apparatus of heading 8519 or 85219Free to 3.9%
8523Discs, tapes, solid-state non-volatile storage devices, "smart cards" and other media for the recording of sound or of other phenomena, whether or not recorded, including matrices and masters for the production of discs, but excluding products of Chapter 3725Free
8524Flat panel display modules, whether or not incorporating touch-sensitive screens8Free to 4.5%
8525Transmission apparatus for radio-broadcasting or television, whether or not incorporating reception apparatus or sound recording or reproducing apparatus; television cameras, digital cameras and video camera recorders21Free
8526Radar apparatus, radio navigational aid apparatus and radio remote control apparatus6Free
8527Reception apparatus for radiobroadcasting, whether or not combined, in the same housing, with sound recording or reproducing apparatus or a clock27Free to 2%
8528Monitors and projectors, not incorporating television reception apparatus; reception apparatus for television, whether or not incorporating radio-broadcast receivers or sound or video recording or reproducing apparatus79Free to 5%
8529Parts suitable for use solely or principally with the apparatus of headings 8524 to 852846Free
8530Electrical signaling, safety or traffic control equipment for railways, streetcar lines, subways, roads, inland waterways, parking facilities, port installations or airfields (other than those of heading 8608); parts thereof3Free
8531Electric sound or visual signaling apparatus (for example, bells, sirens, indicator panels, burglar or fire alarms), other than those of heading 8512 or 8530; parts thereof16Free to 1.3%
8532Electrical capacitors, fixed, variable or adjustable (pre-set); parts thereof29Free
8533Electrical resistors (including rheostats and potentiometers), other than heating resistors; parts thereof25Free
8534Printed circuits7Free
8535Electrical apparatus for switching or protecting electrical circuits, or for making connections to or in electrical circuits (for example, switches, fuses, lightning arresters, voltage limiters, surge suppressors, plugs and other connectors, junction boxes), for a voltage exceeding 1,000 V122% to 2.7%
8536Electrical apparatus for switching or protecting electrical circuits, or for making connections to or in electrical circuits (for example, switches, relays, fuses, surge suppressors, plugs, sockets, lamp-holders and other connectors, junction boxes), for a voltage not exceeding 1,000 V; connectors for optical fibers, optical fiber bundles or cables43Free to 2.7%
8537Boards, panels, consoles, desks, cabinets and other bases, equipped with two or more apparatus of heading 8535 or 8536, for electric control or the distribution of electricity, including those incorporating instruments or apparatus of chapter 90, and numerical control apparatus, other than switching apparatus of heading 851710Free to 2.7%
8538Parts suitable for use solely or principally with the apparatus of heading 8535, 8536 or 85379Free to 3.5%
8539Electrical filament or discharge lamps, including sealed beam lamp units and ultraviolet or infrared lamps; arc lamps; light-emitting diode (LED) light sources; parts thereof40Free to 5.8%
8540Thermionic, cold cathode or photocathode tubes (for example, vacuum or vapor or gas filled tubes, mercury arc rectifying tubes, cathode-ray tubes, television camera tubes); parts thereof38Free to 15%
8541Semiconductor devices (for example, diodes, transistors, semiconductor-based transducers); photosensitive semiconductor devices, including photovoltaic cells whether or not assembled in modules or made up into panels; light-emitting diodes (LED), whether or not assembled with other light-emitting diodes (LED); mounted piezo-electric crystals; parts thereof36Free
8542Electronic integrated circuits; parts thereof31Free
8543Electrical machines and apparatus, having individual functions, not specified or included elsewhere in this chapter; parts thereof33Free to 2.6%
8544Insulated (including enameled or anodized) wire, cable (including coaxial cable) and other insulated electric conductors, whether or not fitted with connectors; optical fiber cables, made up of individually sheathed fibers, whether or not assembled with electric conductors or fitted with connectors19Free to 5.3%
8545Carbon electrodes, carbon brushes, lamp carbons, battery carbons and other articles of graphite or other carbon, with or without metal, of a kind used for electrical purposes8Free
8546Electrical insulators of any material5Free to 3%
8547Insulating fittings for electrical machines, appliances or equipment, being fittings wholly of insulating material apart from any minor components of metal (for example, threaded sockets) incorporated during molding solely for the purposes of assembly, other than insulators of heading 8546; electrical conduit tubing and joints therefor, of base metal lined with insulating material7Free to 4.6%
8548Electrical parts of machinery or apparatus, not specified or included elsewhere in this chapter1Free
8549Electrical and electronic waste and scrap14Free

The heading with a single HTS code

These headings have one ten digit code each, so the code and its rates are here in full.

8548: Electrical parts of machinery or apparatus

“Electrical parts of machinery or apparatus, not specified or included elsewhere in this chapter.”

HTS code
8548.00.00.00
General
Free
Column 2
35%
Units
No.
Special
None listed
Price it

The most common general duty rates in chapter 85

General duty rateHTS codes
Free566
2.7%54
2.5%47
2%28
3.9%27
3.5%23
5%23
2.6%21

Chapter 85 notes

The legal notes at the head of the chapter decide what it covers and what it leaves to other chapters, so read them before you settle on a heading. They are the schedule’s own text, 4,092 words.

Read the chapter 85 notes

Notes

1. This chapter does not cover:

(a) Electrically warmed blankets, bed pads, foot-muffs or the like; electrically warmed clothing, footwear or ear pads or other electrically warmed articles worn on or about the person;

(b) Articles of glass of heading 7011;

(c) Machines and apparatus of heading 8486;

(d) Vacuum apparatus of a kind used in medical, surgical, dental or veterinary sciences (heading 9018); or

(e) Electrically heated furniture of chapter 94.

2. Headings 8501 to 8504 do not apply to goods described in heading 8511, 8512, 8540, 8541 or 8542.

However, metal tank mercury arc rectifiers remain classified in heading 8504.

3. For the purposes of heading 8507, the expression "electric accumulators" includes those presented with ancillary components which contribute to the accumulator's function of storing and supplying energy or protect it from damage, such as electrical connectors, temperature control devices (for example, thermistors) and circuit protection devices. They may also include a portion of the protective housing of the goods in which they are to be used.

4. Heading 8509 covers only the following electromechanical machines of the kind commonly used for domestic purposes:

(a) Floor polishers, food grinders and mixers, and fruit or vegetable juice extractors, of any weight;

(b) Other machines provided the weight of such machines does not exceed 20 kg, exclusive of extra interchangeable parts or detachable auxiliary devices.

The heading does not, however, apply to fans or ventilating or recycling hoods incorporating a fan, whether or not fitted with filters (heading 8414), centrifugal clothes dryers (heading 8421), dishwashing machines (heading 8422), household washing machines (heading 8450), roller or other ironing machines (heading 8420 or 8451), sewing machines (heading 8452), electric scissors (heading 8467) or to electrothermic appliances (heading 8516).

5. For the purposes of heading 8517, the term ?smartphones? means telephones for cellular networks, equipped with a mobile operating system designed to perform the functions of an automatic data processing machine such as downloading and running multiple applications simultaneously, including third-party applications, and whether or not integrating other features such as digital cameras and navigational aid systems.

6. For the purposes of heading 8523:

(a) "Solid-state non-volatile storage devices "(for example,"flash memory cards" or "flash electronic storage cards") are storage devices with a connecting socket, comprising in the same housing one or more flash memories (for example, "FLASH E²PROM") in the form of integrated circuits mounted on a printed circuit board. They may include a controller in the form of an integrated circuit and discrete passive components, such as capacitors and resistors;

(b) The term "smart cards" means cards which have embedded in them one or more electronic integrated circuits (a microprocessor, random access memory (RAM) or read-only memory (ROM)) in the form of chips. These cards may contain contacts, a magnetic stripe or an embedded antenna but do not contain any other active or passive circuit elements.

7. For the purposes of heading 8524, ?flat panel display modules? refer to devices or apparatus for the display of information equipped at a minimum with a display screen, which are designed to be incorporated into articles of other headings prior to use. Display screens for flat panel display modules include, but are not limited to, those which are flat, curved, flexible, foldable or stretchable in form. Flat panel display modules may incorporate additional elements, including those necessary for receiving video signals and the allocation of those signals to pixels on the display. However, heading 8524 does not include display modules which are equipped with components for converting video signals (e.g., a scaler IC, decoder IC or application processer) or have otherwise assumed the character of goods of other headings.

For the classification of flat panel display modules defined in this Note, heading 8524 shall take precedence over any other heading in the tariff schedule.

8. For the purposes of heading 8534 "printed circuits" are circuits obtained by forming on an insulating base, by any printing process (for example, embossing, plating-up, etching) or by the "film circuit" technique, conductor elements, contacts or other printed components (for example, inductances, resistors, capacitors) alone or interconnected according to a pre-established pattern, other than elements which can produce, rectify, modulate or amplify an electrical signal (for example, semiconductor elements).

The term "printed circuits" does not cover circuits combined with elements other than those obtained during the printing process, nor does it cover individual, discrete resistors, capacitors or inductances. Printed circuits may, however, be fitted with non-printed connecting elements.

Thin- or thick-film circuits comprising passive and active elements obtained during the same technological process are to be classified in heading 8542.

9. For the purpose of heading 8536, "connectors for optical fibres, optical fibre bundles or cables" means connectors that simply mechanically align optical fibres end to end in a digital line system. They perform no other function, such as the amplification, regeneration or modification of a signal.

10 Heading 8537 does not include cordless infrared devices for the remote control of television receivers or other electrical equipment (heading 8543).

11. For the purposes of heading 8539, the expression "light-emitting diode (LED) light sources" covers:

(a) "Light-emitting diode (LED) modules" which are electrical light sources based on light-emitting diodes (LED) arranged in electrical circuits and containing further elements like electrical, mechanical, thermal or optical elements. They also contain discrete active elements, discrete passive elements, or articles of heading 8536 or 8542 for the purposes of providing power supply or power control. Light-emitting diode (LED) modules do not have a cap designed to allow easy installation or replacement in a luminaire and ensure mechanical and electrical contact.

(b) "Light-emitting diode (LED) lamps" which are electrical light sources containing one or more LED modules containing further elements like electrical, mechanical, thermal or optical elements. The distinction between light-emitting diode (LED) modules and light-emitting diode (LED) lamps is that lamps have a cap designed to allow easy installation or replacement in a luminaire and ensure mechanical and electrical contact.

12. For the purposes of headings 8541 and 8542:

(a) (i) "Semiconductor devices" are semiconductor devices the operation of which depends on variations in resistivity on the application of an electric field or semiconductor-based transducers.

Semiconductor devices may also include assembly of plural elements, whether or not equipped with active and passive device ancillary functions.

"Semiconductor-based transducers" are, for the purposes of this definition, semiconductor-based sensors, semiconductor-based actuators, semiconductor-based resonators and semiconductor-based oscillators, which are types of discrete semiconductor-based devices, which perform an intrinsic function, which are able to convert any kind of physical or chemical phenomena or an action into an electrical signal or an electrical signal into any type of physical phenomenon or an action.

All the elements in semiconductor-based transducers are indivisibly combined, and may also include necessary materials indivisibly attached, that enable their construction or function.

The following expressions mean:

(1) "Semiconductor-based" means built or manufactured on a semiconductor substrate or made of semiconductor materials, manufactured by semiconductor technology, in which the semiconductor substrate or material plays a critical and unreplaceable role of transducer function and performance, and the operation of which is based on semiconductor properties including physical, electrical, chemical and optical properties.

(2) "Physical or chemical phenomena" relate to phenomena, such as pressure, acoustic waves, acceleration, vibration, movement, orientation, strain, magnetic field strength, electric field strength, light, radioactivity, humidity, flow, chemicals concentration, etc.

(3) "Semiconductor-based sensor" is a type of semiconductor device, which consists of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of detecting physical or chemical quantities and converting these into electric signals caused by resulting variations in electric properties or displacement of a mechanical structure.

(4) "Semiconductor-based actuator" is a type of semiconductor device, which consists of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of converting electric signals into physical movement.

(5) "Semiconductor-based resonator" is a type of semiconductor device, which consists of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of generating a mechanical or electrical oscillation of a predefined frequency that depends on the physical geometry of these structures in response to an external input.

(6) "Semiconductor-based oscillator" is a type of semiconductor device, which consists of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of generating a mechanical or electrical oscillation of a predefined frequency that depends on the physical geometry of these structures.

(ii) "Light-emitting diodes (LED)" are semiconductor devices based on semiconductor materials which convert electrical energy into visible, infra-red or ultra-violet rays, whether or not electrically connected among each other and whether or not combined with protective diodes. Light-emitting diodes (LED) of heading 8541 do not incorporate elements for the purposes of providing power supply or power control;

(b) "Electronic integrated circuits" are:

(i) Monolithic integrated circuits in which the circuit elements (diodes, transistors, resistors, capacitors, inductances, etc.) are created in the mass (essentially) and on the surface of a semiconductor or compound semiconductor material (for example, doped silicon, gallium arsenide, silicon germanium, iridium phosphide) and are inseparably associated;

(ii) Hybrid integrated circuits in which passive elements (resistors, capacitors, inductances, etc.), obtained by thin- or thick-film technology, and active elements (diodes, transistors, monolithic integrated circuits, etc.), obtained by semiconductor technology, are combined to all intents and purposes indivisibly, by interconnections or interconnecting cables, on a single insulating substrate (glass, ceramic, etc.). These circuits may also include discrete components;

(iii) Multichip integrated circuits consisting of two or more interconnected monolithic integrated circuits combined to all intents and purposes indivisibly, whether or not on one or more insulating substrates, with or without leadframes, but with no other active or passive circuit elements.

(iv) Multi-component integrated circuits (MCOs): a combination of one or more monolithic, hybrid, or multi-chip integrated circuits with at least one of the following components: silicon-based sensors, actuators, oscillators, resonators or combinations thereof, or components performing the functions of articles classifiable under heading 8532, 8533, 8541, or inductors classifiable under heading 8504, formed to all intents and purposes indivisibly into a single body like an integrated circuit, as a component of a kind used for assembly onto a printed circuit board (PCB) or other carrier, through the connecting of pins, leads, balls, lands, bumps, or pads.

For the purpose of this definition:

1. ?Components? may be discrete, manufactured independently then assembled onto the rest of the MCO, or integrated into other components.

2. ?Silicon-based? means built on a silicon substrate, or made of silicon materials, or manufactured onto integrated circuit die.

3. (a) "Silicon-based sensors" consist of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of detecting physical or chemical phenomena and transducing these into electric signals, caused by resulting variations in electric properties or displacement of a mechanical structure. "Physical or chemical phenomena" relates to phenomena, such as pressure, acoustic waves, acceleration, vibration, movement, orientation, strain, magnetic field strength, electric field strength, light, radioactivity, humidity, flow, chemicals concentration, etc.

(b) ?Silicon-based actuators? consist of microelectronic and mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of converting electrical signals into physical movement.

(c) ?Silicon-based resonators? are components that consist of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and have the function of generating a mechanical or electrical oscillation of a predefined frequency that depends on the physical geometry of these structures in response to an external input.

(d) ?Silicon-based oscillators? are active components that consist of microelectronic or mechanical structures that are created in the mass or on the surface of a semiconductor and that have the function of generating a mechanical or electrical oscillation of a predefined frequency that depends on the physical geometry of these structures.

For the classification of the articles defined in this note, headings 8541 and 8542 shall take precedence over any other heading in the Nomenclature, except in the case of heading 8523, which might cover them by reference to, in particular, their function.

Subheading Notes

1. Subheading 8525.81 covers only high-speed television cameras, digital cameras and video camera recorders having one or more of the following characteristics:

- writing speed exceeding 0.5 mm per microsecond;

- time resolution 50 nanoseconds or less;

- frame time exceeding 225,000 frames per second.

2. In respect of subheading 8525.82, radiation-hardened or radiation-tolerant television cameras, digital cameras and video camera recorders are designed or shielded to enable operation in a high-radiation environment. These cameras are designed to withstand a total radiation dose of at least 50 x 103 Gy (silicon)(5 x 106 RAD (silicon)), without operational degradation.

3. Subheading 8525.83 covers night vision television cameras, digital cameras and video camera recorders which use a photocathode to convert available light to electrons, which can be amplified and converted to yield a visible image. This subheading excludes thermal imaging cameras (generally subheading 8525.89).

4. Subheading 8527.12 covers only cassette players with built-in amplifier, without built-in loudspeaker, capable of operating without an external source of electric power and the dimensions of which do not exceed 170 mm x 100 mm x 45 mm.

5. For the purposes of subheadings 8549.11 to 8549.19, ?spent primary cells, spent primary batteries and spent electric accumulators: are those which are neither usable as such because of breakage, cutting-up, wear or other reasons, nor capable of being recharged.

Additional U.S. Notes

1. For the purposes of headings 8501 and 8503, 746 watts (W) is taken to be equivalent to 1 horsepower (hp).

2. For the purposes of subheading 8516.72, the term "toasters" includes toaster-ovens which are designed essentially for toasting bread but can also bake small items, such as potatoes.

3. For the purposes of headings 8517 and 8525 the term "transceivers" refers to combinations of radio transmitting and receiving equipment in a common housing, employing common circuit components for both transmitting and receiving, and which are not capable of simultaneously receiving and transmitting.

4. For the purposes of 8529.90.05, 8529.90.06, 8529.90.33, 8529.90.36, 8529.90.43, 8529.90.46, 8529.90.88 and 8529.90.89:

(a) Each subassembly that contains as a component, or is covered in the same entry with, one or more of the following television components, viz.,

tuner, channel selector assembly, antenna, deflection yoke, degaussing coil, picture tube mounting bracket, grounding assembly, parts necessary for fixing the picture tube or tuner in place, consumer-operated controls or speaker,

shall be classified in subheading 8529.90.05, 8529.90.33, 8529.90.43 or 8529.90.88, as appropriate; and

(b) Each subassembly shall be counted as a single unit, except that two or more different printed circuit boards or ceramic substrates covered by the same entry and designed for assembly into the same television models shall be counted as one unit.

5. Picture tubes imported in combination with, or incorporated into, other articles are to be classified in subheadings 8540.11 through 8540.12, inclusive, unless they are--

(a) incorporated into complete television receivers, as defined in additional U.S. note 6 below;

(b) incorporated into fully assembled units such as word processors, ADP terminals, or similar articles;

(c) put up in kits containing all the parts necessary for assembly into complete television receivers, as defined in additional U.S. note 6 below; or

(d) put up in kits containing all the parts necessary for assembly into fully assembled units such as word processors, ADP terminals, or similar articles.

6. For the purposes of additional U.S. note 5 above the term "complete television receivers" means television receivers, fully assembled in their cabinets, whether or not packaged or tested for distribution to the ultimate purchaser(s).

7. For the purposes of this chapter, references to "high definition" as it applies to television receivers and cathode-ray tubes refer to articles having:

(a) a screen aspect ratio equal to or greater than 16:9; and

(b) a viewing screen capable of displaying more than 700 scanning lines.

8. For the purposes of this chapter, the video display diagonal is determined by measuring the maximum straight line dimension across the visible portion of the faceplate used for displaying video.

9. Subheadings 8529.90.29, 8529.90.33, 8529.90.36 and 8529.90.39 cover the following parts of television receivers (including video monitors and video projectors):

(a) Video intermediate (IF) amplifying and detecting systems;

(b) Video processing and amplification systems;

(c) Synchronizing and deflection circuitry;

(d) Tuners and tuner control systems; and

(e) Audio detection and amplification systems.

10. For the purposes of subheading 8540.91.15, the term "front panel assembly" refers to:

(a) with respect to a color cathode-ray television picture tube, an assembly which consists of a glass panel and a shadow mask or aperture grille, attached for ultimate use, which is suitable for incorporation into a color cathode-ray television picture tube (including video monitor cathode-ray tube), and which has undergone the necessary chemical and physical processes for imprinting phosphors on the glass panel with sufficient precision to render a video image when excited by a stream of electrons; or

(b) with respect to a monochrome cathode-ray picture tube, an assembly which consists of either a glass panel or a glass envelope, which is suitable for incorporation into a monochrome cathode-ray television picture tube (including video monitor or video projector cathode-rate tube), and which has undergone the necessary chemical and physical processes for imprinting phosphors on the glass panel or glass envelope with sufficient precision to render a video image when excited by a stream of electrons.

11. For the purposes of subheading 8538.90.10, the expression "articles described in additional U.S. note 11 to chapter 85" means any of the following goods: photocopying apparatus of subheading 8443.32.30, 8443.32.50, 8443.39.20 or 8443.39.40; word processing machines of heading 8469; articles of heading 8470 or heading 8471; automatic teller machines of subheading 8472.90.10; articles of subheadings 8486.10 through 8486.40; articles of heading 8517; articles of subheading 8519.50; transmission apparatus of subheading 8525.50.10; articles of subheading 8525.60; digital still image cameras of subheading 8525.89.40; articles of subheading 8543.70.93; plotters of subheading 9017.10.40 or 9017.20.70; instruments and apparatus of heading 9026; instruments and apparatus of heading 9027 except of subheading 9027.10 or 9027.90.20; instruments and apparatus of subheading 9030.40; instruments and apparatus of subheading 9030.82; optical instruments and appliances of subheading 9031.41; optical instruments and appliances of subheading 9031.49.70; articles of subheading 9031.80.40.

12. For the purposes of subheading 8517.69.00, the term "paging receivers" includes paging alert devices designed merely to emit a sound or visual signal (e.g., flashing light) upon the reception of a pre-set radio signal.

Statistical Notes

1. For the purposes of this chapter the terms "AM" and "FM" refer to the entertainment broadcast bands of 550-1650 kHz and 88-108MHz, respectively.

2. For the purposes of statistical reporting number 8507.60.0030, the term ?battery energy storage system? consists of an electrochemical device that has the following characteristics:

(a) is designed to (i) store collected energy and (ii) discharge stored energy;

(b) consists of one or more lithium-ion battery modules, battery management circuitry, and other components to enable the storage or discharge of energy;

(c) has a minimum energy capacity of one kilowatt-hour; and

(d) is fully encased within a housing.

3. For statistical reporting purposes under subheading 8539.10, the size of a sealed beam lamp unit is determined by measuring the largest diagonal dimension across the faceplate.

4. For statistical reporting purposes under subheading 8544.70, the unit of quantity "fiber m", as it pertains to optical fiber cables, is determined by multiplying the number of individual fibers contained therein by the length in meters.

5. For statistical reporting purposes in heading 8542 the following definitions will apply:

(a) The term "static read-write random access (SRAM)" refers to integrated circuit memory devices in which the memory cells may be addressed in any sequence, randomly, for the storage or retrieval of data and in which in which the stored information is retained without further intervention as long as electric power is supplied to the device.

(b) The term "volatile memory" refers to integrated circuit memory devices which lose all stored information in the absence of electric power.

(c) The term "dynamic read-write random access (DRAM)" refers to integrated circuit memory devices in which the memory cells may be addressed in any sequence, randomly, for the storage or retrieval of data and in which the stored information must continually be refreshed in order to hold the information in memory.

(d) The term "electrically erasable programmable read-only memory (EEPROM)" refers to user programmable integrated circuit memory devices which retain the stored information in the absence of electric power and in which the stored information may be altered electrically.

(e) The term "erasable (except electrically) programmable read-only memory (EPROM)" refers to user programmable integrated circuit memory devices which retain the stored information in the absence of electric power and from which the stored information may be removed (except electrically). Such devices are usually erased by exposure to ultraviolet light after which they may be rewritten with new information.

(f) The term "microprocessor" refers to a central processing unit (CPU) fabricated as a monolithic integrated circuit.

(g) The term "kilobit" refers to 1,024 bits of data storage capacity, the term "megabit" refers to 1,024 kilobits of data storage capacity, and the term "gigabit" refers to 1,024 megabits of data storage capacity.

6. For statistical reporting purposes under subheading 8532.22, the diameter of aluminum electrolytic capacitors not having a circular cross-section shall be the maximum dimension measured through the center.

7. For the purposes of statistical reporting number 8544.42.9010, "Extension cords" is defined as a flexible cord assembly incorporating an electrical plug conforming to types 1-15P, 5-15P or 5-20P of the National Electrical Manufacturers Association (NEMA) and one or more receptacles conforming to NEMA type 1-15R, 5-15R or 5-20R.

8. For statistical reporting purposes under subheading 8539.52.00, the types of light-emitting (LED) lamps are defined by American National Standards Institute for Electric Lamps as follows:

(a) ANSI shapes A, BT, P, PS or T described under 8539.52.0010, except for the straight linear tubes or U-shaped tubes of statistical reporting number 8539.52.0051;

(b) ANSI shapes B, BA, C, CA, DC, F, G or ST described under 8539.52.0020;

(c) ANSI shapes R, BR or PAR described under 8539.52.0030; or

(d) ANSI shapes MR11, MR16 or MRX16 described under 8539.52.0040.

9. For the purposes of heading 8501, photovoltaic generators consist of panels of photocells combined with other apparatus, e.g., storage batteries and electronic controls (voltage regulator, inverter, etc.) and panels or modules equipped with elements, however simple (for example, diodes to control the direction of the current), which supply the power directly to, for example, a motor, an electrolyser. In these devices, electricity is produced by means of solar cells which convert solar energy directly into electricity (photovoltaic conversion).

10. For the purposes of statistical reporting numbers 8501.71.0000, 8501.72.1000, 8501.72.2000, 8501.72.3000, 8501.72.9000, 8501.80.1000, 8501.80.2000, 8501.80.3000, 8501.80.9000, 8541.42.0010, 8541.42.0080, 8541.43.0010 and 8541.43.0080, importers should report the total watts at maximum power based on standard test conditions according to the latest revision of International Electrotechnical Commission (IEC) 60904, "Photovoltaic Devices.?

11. For the purposes of calculating the second unit of quantity for statistical reporting numbers under subheadings 8504.21.00, 8504.22.00, 8504.23.00, 8504.32.00, 8504.33.00 and 8504.34.00, the weight of the transformers is the total weight of the transformer from the nameplate, included cooling equipment and systems, such as coolant oils, heat exchangers, fans, tanks, and insulation; bushings; cores; coils; and tap changes, but not:

(a) Pallets or other rigging needed exclusively for shipping or transportation; and

(b) Other ancillary electrical equipment that may be attached to the transformer which performs a function unrelated to the changing of alternating current voltage levels.

12. For the purposes of statistical reporting numbers 8541.42.0010 and 8541.43.0010, the term "crystalline silicon photovoltaic cells" means crystalline silicon photovoltaic cells of a thickness equal to or greater than 20 micrometers, having a p/n junction (or variant thereof) formed by any means, whether or not the cell imported under statistical reporting number 8541.42.0010 (or subassemblies thereof imported under statistical reporting number 8541.43.0010) has undergone other processing, including, but not limited to, cleaning, etching, coating, and/or addition of materials (including, but not limited to, metallization and conductor patterns) to collect and forward the electricity that is generated by the cell. Such cells include photovoltaic cells that contain crystalline silicon in addition to other photovoltaic materials. This includes, but is not limited to, passivated emitter rear contact cells, heterojunction with intrinsic thin-layer cells, and other so-called hybrid cells.

Section XVI: the 2 chapters

  • Chapter 84: Nuclear reactors, boilers, machinery and mechanical appliances; parts thereof
  • Chapter 85: Electrical machinery and equipment and parts thereof; sound recorders and reproducers, television image and sound recorders and reproducers, and parts and accessories of such articles (this chapter)

Before you file

The importer is responsible for the classification it declares, and a licensed customs broker confirms it. Warp is not a customs broker, and these pages are not customs advice. The rates here are the schedule’s own columns: additional duties that depend on the country of origin, such as Section 301, sit in chapter 99 and are not in them, and neither are the entry fees. The landed cost calculator adds the ones it covers, and the HTS code lookup searches every line by product.

Source: Harmonized Tariff Schedule of the United States, US International Trade Commission, Revision 23 (2026). Codes, descriptions, duty rates and units read November 14, 2026. Chapter notes read November 16, 2026.